Vehicles
Sections
139 not categorized PORSCHE 987 PLATESCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1989-94 (includes uncategorized and accessory items) NLA72355305 Two required per vehicle replaces 64472355305
$7.85
Make a selection FVD116805 Replacing your pressure plate? Take a look at this lightweight model, a savings of over 11 lbs for some models. Made by zf sachs to original specifications for all 964 / 993 and 968 naturally aspirated models. Direct replacement for the oe pressure plate. 240 mm. 3100-3300 lb. Clamp load. Weighs: 9.5 lbs. (4.3 kg) installation notes for those using single mass flywheels: when installing a new pressure plate, be sure to add 9 qty. Pressure plate pan head bolts, our part # 90006710301 and 1 qty. Starter ring gear 96411414331. General Fitment911 1994-98968 1992-95 911 1989-94
From $581.90
Make a selection FVD116926
General Fitment911 GT3 2003-05911 TURBO/GT2 2001-05 911 1994-98 911 1989-94
$729.45
Make a selection FVD33310003 FVD-alu-camberplates replace soft top strut rubber bushings. The FVD-camberplates are machined from billeted aluminum, providing you with a wide range of camber possibilities. General Fitment911 1989-94
$451.07
Make a selection FVD33300905 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: made from ¼ inch spring steel includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car.
$273.90
Make a selection FVD33310002 FVD-alu-camberplates replace soft top strut rubber bushings. The FVD-camberplates are machined from billeted aluminum, providing you with a wide range of camber possibilities. Original-shocks and cup-shocks. General Fitment911 1989-94
$434.30
Make a selection FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD3439642PSS9 The FVD camber plate kit replaces the front and rear original rubber top strut mount bushings. We manufacture each camber plate and mount in Germany and machine each from a solid block of billet aluminum. Each is fitted with spherical bearings which allows a wide range of camber possibilities. This kit contains: 2 front camber plates 2 rear camber plates please note: this kit only works in conjunction with a pss9 / pss10 coil over (double spring) suspension in front and rear. General Fitment911 1989-94
From $1,204.50
Make a selection FVD34310002R FVD-alu-camberplates replace soft top strut rubber bushings. The FVD-camberplates are machined from billeted aluminum, providing you with a wide range of camber possibilities. You can get up to 4 degrees negative camber. FVD-alu-camberplates fits on original-shocks and cup-shocks. General Fitment911 1989-94
$477.05
Make a selection FVD343997PSS
$893.46
Make a selection FVD721805000 Aligns the drill bit when removing broken studs.
$491.70
Make a selection FVD721VW401
$128.70
Make a selection FVD53191101 As a striker plate ages, it will start to rattle and can potentially be a safety risk. Repair it with this high-quality replacement sourced in Germany. We recommend adding new striker plates gaskets, either 90153170323 or 90153170324 depending on what thickness you need. If new screws are necessary use part # 99921900800 sold individually. One kit is required per striker plate.
$44.00
Make a selection I200 Heater control block off plates - until now, removing the center console from your 964/993 was not possible due to the required switches that were mounted in it. Rennline's new radio and heater control block off plates solve that problem. These plates have been specially designed to accept the factory switches installed in the center console of all 964/993 cars. Don't have the factory switches? No problem. These plates are also available without switch cutouts so you can install your own switches or gauges. Made from powder coated metal and installs in minutes on cars with the radio or heater controls removed. General Fitment911 1989-94911 1994-98
$50.00
Make a selection I203 Radio and heater control block off plates - until now, removing the center console from your 964/993 was not possible due to the required switches that were mounted in it. Rennline's new radio and heater control block off plates solve that problem. These plates have been specially designed to accept the factory switches installed in the center console of all 964/993 cars. Don't have the factory switches? No problem. These plates are also available without switch cutouts so you can install your own switches or gauges. Made from powder coated metal and installs in minutes on cars with the radio or heater controls removed. General Fitment911 1989-94911 1994-98
$50.00
Make a selection KEV503032001
$127.60
Make a selection G831927 This bracket is for plates that measure 20.5x4.5 inches, which is the European standard. This bracket is easy to install and also easy to use with your plates. Made of high quality molded plastic and very durable. Combine this bracket with our euro plates for a fantastic look on your Porsche. General FitmentACCESSORY
$35.40
Make a selection
$1.49
Make a selection
$46.48
Make a selection
$7.65
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |